Knife Guide: Cuts off the extra media easily along the groove. If any of the following occurs, which means the blade has reached the end of its life. Note: Before contacting your local dealer, please make sure that the problems are coming from your cutting plotter, not from the communication between the computer and cutting plotter or from a malfunction in your computer or software. Turn off the cutting plotter and turn it on again to see if the problem still exists. Do not touch the tip of the blade with your fingers. Note: The new origin will be set at the position of the tool carriage after the cutting test.
GCC JaguarIII USB Free Driver Download for Windows Vista, 2003, XP, 2000, NT4, NT3.51, ME, 98SE, 98, 95 (1276219)
Media Loading Width Acceptable Material Thickness Number of Pinch Rollers Motor Cutting Force Max. Insert screws into the holes of the stand-right and stand-left Then use screw driver to tighten stand beam, stand-right, stand-left and roll holder supportsBobcat Users Guide2-2Step 3. After the adjustment, click Loop Detect again. Connect the power cable to a grounded outlet. In this case, the maximum plotting length is 25000mm, and the distance between the farthest two pinch rollers is 277. Clean the platen, paper sensors and the pinch rollers with a water-rinsed cloth or alcohol-rinsed cloth. The value of the cutting speed can be changed from the driver.
Bobcat Bi 60 30 Driver
Warning 3 Lever up or no media Check that you have lowered the lever down and make sure that you load the media before cutting. In this case, the actual cutting width of the rectangle is 49mm. If the square can be easily peeled off from the media, the setting of the cutting force is appropriate. Then press the arrow buttons to move the tool carriage to the position where you want to make the cut test. E nesse vídeo aparece como nome de. Re-scale the graph to a smaller size.
Driver Download for CoCut
If you wish to cut in a portrait fashion simply rotate your graphics. If the serial cable you are using wasn't. You can also cut off the extra media with the cutting plotter tool along the knife guide Figure 2. If your cutting plotter doesnt plot, please check the following items first:Is the power cord plugged in properly? Refer to the following chart to understand what represented by each light on the control panel. You can solve the problem by: 1. Move the pinch rollers to widen the cutting area. The cutting plotter is ready to receive data from the host computer.
Bobcat/Sable BI
There should be at least two people holding the machine from its left and right bottom sides while unpacking, installing or relocating the cutting plotter. Then send the cutting job again from your computer to the cutting plotter. If so, then check whether the interface settings are correct. Is the power switch turned on properly? Centronics Connect the parallel cable to the cutting plotter and the host computer Figure3-1. Grid Drum: Moves the media back and forth during the operation. Choosing a proper place before setting up the cutting plotter.
Драйвер Плоттер Bobcat Bi 60
Finally absorb water with a soft, lint-free cloth. You must use a Serial Com port. Keep loose clothing, hair, and any other items away from the grid drum when the cutting plotter is in operation. Do not move it by holding the front rubber roller. Figure 1-1 Front View of BobcatBobcat Users Guide1-1Figure 1-2 Back View of BobcatLevelPinch rollerBack paper sensor Pinch rollerFig 1-2 Back view of BobcatBobcat Users Guide1-21.
Bobcat Bi 60 30 Driver
One function of the DisDetect key is to release the port. Sharp blade with smallest offset. Bobcat Users Guide6-3Note: In order to identify the warning messages easily, please stick the warning sticker in accessory box on the side cover of your cutting plotter. SignTools 3 contains plotter drivers for over 300 popular cutters. You will then be able to see the new values In this case, the Force was changed from 200 to 277, see figure 4.
Bobcat/Sable BI
Insert roll holders into roll holder support. Error 4 Check media, or Y motor carriage driven motor This message indicates that there might be an obstruction to the carriage relating to a problem on the Y-axis. Make sure all of the options are ticked and click on the Save Settings Now button. Then turn on the power and reboot the cutting plotter. Please note that the new origin setting must be made under the off-line condition.
-
